荔灣3

中化建國際 對下列產品及服務進行國際公開競爭性招標，于2025-03-17在公告。本次招標采用傳統招標方式，現邀請合格投標人參加投標。1、招標條件項目概況:荔灣3-1 氣田群位于中國南海珠江口盆地白云凹陷內，距香港東南部310km，氣田群所在海域水深640-1500m。荔灣3-1 氣田調整開發項目通過降低荔灣3-1 氣田群水下井口壓力實現增產，無調整井及新建平臺設施。平臺增壓部分在荔灣3-1CEP 平臺新建3 臺預增壓濕氣壓縮機、入口滌氣罐及出口冷卻器和1 臺段塞流捕集器，改造凝析油增壓泵。平臺增壓部分計劃于2027年1 月投用。資金到位或資金來源落實情況:已落實項目已具備招標條件的說明:已具備2、招標內容招標項目編號:0704-2540JDCP5700招標項目名稱:荔灣3-1氣田調整開發項目調節閥項目實施地點:中國廣東省招標產品列表(主要設備):

序號	產品名稱	數量	簡要技術規格	備注
1	調節閥	15	詳見技術文件

3、投標人資格要求投標人應具備的資格或業績:對投標人的資格和業績要求：Requirements for Qualification and reference of Bidder:（1）資格要求 Requirements for Qualification of Bidder A．★營業執照：如果投標人為境內注冊公司，投標人需提供合法有效的企業法人營業執照、稅務登記證及組織機構代碼證或證照合一的營業執照；如果投標人為境外注冊公司，需提供有效的公司登記注冊證明。A．★Business licence: The bidder within the customs territory shall provide valid independent legal person business license, tax registration certificate, organization code certificate, or combined certificate and business license;The bidder outside the customs territory shall provide valid certificate to prove valid business registration certificate.B．★制造商要求:所投產品為國內產品：不允許代理商投標，投標人需是調節閥的制造商所投產品為境外產品：允許調節閥的制造商或取得調節閥制造商唯一授權的代理商投標。 投標人為代理商時，應得到本次投標調節閥制造商的唯一合法授權，并需提供以下材料（蓋制造商公章）：1）在有效期內的調節閥制造商授權書；2）調節閥制造商承諾函，承諾投標所投產品為制造商工廠生產。B． ★ Manufacturer requirement: The product being bid for is a domestic product: agents are not allowed to bid, and bidders must be manufacturers of control valves.The product being tendered is an overseas product: manufacturers of control valves or agents authorized solely by the control valve manufacturer are allowed to bid.When the bidder is an agent or a contractor, they should obtain the sole legal authorization of the control valve manufacturer for this bidding and provide the following materials (stamped with the manufacturer's official seal):1) Authorization letter from the manufacturer of the control valve within its validity period;2) Commitment letter from the manufacturer of the control valve, promising that the products submitted for bidding will be produced by the manufacturer's factory.C．★是否接受聯合體投標：否。C. ★Joint Venture: Not Accepted.D．★未領購招標文件是否可以參加投標:不可以。D. ★Bid without the bidding documents：NOT Available.（2）★資質要求及證明文件投標人所供的閥門制造商應取得由國家市場監督管理總局頒發的特種設備生產許可證（許可子項目涵蓋A1及A2）及覆蓋本次招標范圍的由第三方頒發的特種設備型式試驗證書,投標人應在投標時提供上述證書的掃描件。The manufacturers of pressure pipeline components such as valves provided by the bidder shall obtain the special equipment manufacturing license (TS A1 or A2 certificate) awarded by State Administration for Market Regulation and the special equipment type test certificate covering the scope of this bidding awarded by third party,Bidders should provide scanned copies of the aforementioned certificates during the bidding process.（3）★業績要求Requirement for Bidder's reference:投標人需滿足以下所有要求：The Bidder needs to meet all below requirements：A.From January 1, 2010 to the bidding deadline (based on the contract signing time), the control valve manufacturer submitted by the bidder must have at least 3 sets of pneumatic control valves and 2 sets of electric control valve matching supply performance. The brand and Production factory address of the control valve submitted by the bidder must be consistent with the performance of the control valve mentioned above(The Production factory address of valve PV-1503D should be consistent with the performance Production factory address corresponding to performance requirement 1, the Production factory address of other pneumatic control valves should be consistent with the performance Production factory addresss corresponding to performance requirement 2, and the Production factory address of electric control valves should be consistent with the performance Production factory address corresponding to performance requirement 3). The performance should meet or exceed the following technical requirements:Performance Requirement 1 Performance Requirement 2 Performance Requirement 3pneumatic control valve pneumatic control valve electric control valvePerformance requirement: 1 set Performance requirement: 2 set Performance requirement: 2 setbody material A182 F51 or A995 Gr.4A body material A995 Gr.4A body material A995 Gr.4ABody size ≥20” Body size ≥14” Body size ≥3”Body rating ≥1500# Body rating ≥600# Body rating ≥300#Body type V-Ball or Globe Body type Globe Body type GlobeFlow coefficient CV CV ≥ 261 at minimum flow rate.CV ≥ 1814under normal traffic conditions.CV ≥ 4201 at maximum flow rate. Flow coefficient CV CV ≥67.4 at minimum flow rate. CV≥302under normal traffic conditions, CV≥537at maximum flow rate.. Flow coefficient CV CV ≥3.42at minimum flow rate..CV≥29 under normal traffic conditions.CV≥ 142at maximum flow rate..Open sized 10%-90% Open sized 10%-90% Open sized 10%-90%Bidders must submit a performance table for regulating valves in the prescribed format and provide relevant performance certification documents. The performance certification documents include but are not limited to: 1) a copy of the sales contract and 2) arrival acceptance materials signed or stamped by the user (arrival acceptance form or commissioning acceptance report or other valid proof materials that can prove that the goods under the contract have been received and accepted). The performance certification documents submitted by the bidder must at least reflect the following contents: contract signing time, contract signing page (domestic trade contracts should have both parties' seals, international trade contracts should have both parties' signatures or seals), manufacturer name, goods name, brand and production factory address, supply quantity, technical parameters/indicators (including at least valve body material, valve body class, valve body type, valve body type, CV value, valve allowable opening and calculation sheet), and arrival acceptance materials signed or stamped by the user. If the performance contract is an annual agreement, in addition to providing the annual agreement, corresponding received orders should also be provided, and the order content or number should be associated with the annual agreement. Providing one or more orders and corresponding arrival acceptance materials under the same annual agreement is considered as one valid performance. Failure to submit performance certification documents, or failure to meet the above performance requirements through the provided performance certification documents, shall be deemed as invalid performance.2010年1月1日至投標截止日（以合同簽訂時間為準），投標人所投調節閥的制造商必須至少有3臺氣動調節閥和2臺電動調節閥配套供貨業績。投標人所投的調節閥的品牌和生產工廠 業績中的技術指標應全部達到或超過以下技術要求：業績要求1 業績要求2 業績要求3氣動調節閥 氣動調節閥 電動調節閥業績要求：1套 業績要求：2套 業績要求：2套閥體材質 A182 F51 或A995 Gr.4A 閥體材質 A995 Gr.4A 閥體材質 A995 Gr.4A閥體尺寸 ≥20” 閥體尺寸 ≥14” 閥體尺寸 ≥3”閥體磅級 ≥1500# 閥體磅級 ≥600# 閥體磅級 ≥300#閥體類型 V-Ball 或 Globe 閥體類型 Globe 閥體類型 Globe流量系數CV 最小流量的情況下CV ≥261正常流量的情況下CV≥1814最大流量的情況下CV≥ 4201 流量系數CV 最小流量的情況下CV ≥67.4正常流量的情況下CV≥302最大流量的情況下CV≥ 537 流量系數CV 最小流量的情況下CV ≥3.42正常流量的情況下CV≥29最大流量的情況下CV≥ 142開度 10%-90% 開度 10%-90% 開度 10%-90%投標人須按規定格式提交調節閥業績表，并提交相關業績證明文件。業績證明文件包括但不限于：1）銷售合同復印件和2）用戶簽字或蓋章的到貨驗收材料（到貨驗收單或調試驗收報告或其他可以證明合同項下貨物已經到貨驗收的有效證明材料）。投標人所提交的業績證明文件必須至少體現以下內容：合同簽署時間、合同簽署頁（國內貿易合同應有雙方蓋章，國際貿易合同應有雙方簽字或蓋章）、制造商名稱、貨物名稱、品牌及生產工廠 若業績合同為年度協議，除提供年度協議外，還應提供相應的已到貨訂單，訂單內容或編號應與年度協議相關聯。同一個年度協議下提供1個或以上的訂單及與訂單對應的到貨驗收材料均算為1個有效業績。未提交業績證明文件，或通過所提供的業績證明文件無法認定滿足上述業績要求的，均視為無效業績。B.The brand of the actuator shall meet the requirements of Appendix A. Bidders may recommend other brands that meet the following conditions and are equivalent to the recommended brand in Appendix A. From January 1, 2010 to the bidding deadline (based on the time of contract signing), the bidder or the manufacturer of the actuator submitted by the bidder shall have a performance of supplying no less than 2 regulating valves, and the brand and model of the actuator in the performance shall be consistent with the one used in this bidding. If the actuator is used on a pneumatic regulating valve, the material of the regulating valve body in the performance should be A182F51, the valve body size should be ≥ 20 ", and the valve body pressure scale should be ≥ 1500 #; If the actuator is used on an electric regulating valve, the valve body material of the regulating valve in the performance should be A182F51, the valve body size should be ≥ 3 ", and the valve body pressure rating should be ≥ 300 #. Bidders of other brands equivalent to the recommended brand must provide performance certification documents,★The performance certification documents include but are not limited to: 1) a copy of the sales contract and 2) arrival acceptance materials signed or stamped by the user (arrival acceptance form or commissioning acceptance report or other valid proof materials that can prove that the goods under the contract have been received and accepted). The performance certification documents submitted by the bidder must at least reflect the following contents: contract signing time, contract signing page (domestic trade contracts should have both parties' seals, international trade contracts should have both parties' signatures or seals), manufacturer name, goods name, model and production factory address, supply quantity, technical parameters/indicators (including at least valve body material, valve body size,valve body class, valve body type), and arrival acceptance materials signed or stamped by the user. If the performance contract is an annual agreement, in addition to providing the annual agreement, corresponding received orders should also be provided, and the order content or number should be associated with the annual agreement. Providing one or more orders and corresponding arrival acceptance materials under the same annual agreement is considered as one valid performance. Failure to submit performance certification documents, or failure to meet the above performance requirements through the provided performance certification documents, shall be deemed as invalid performance.he brand of the actuator should meet the requirements of Appendix A. Bidders may recommend other brands that meet the following conditions and are of the same level as the recommended brand in Appendix A. From January 1, 2010 to the bidding deadline (based on the contract signing time), the bidder shall have a performance of supplying no less than 2 sets/sets of regulating valves for key components of the same level brand. If the actuator is used on pneumatic regulating valves, the material of the regulating valve in the performance should be A182F51, size ≥ 20 ", and pressure rating ≥ 1500 #; If the actuator is used on an electric control valve, the material of the control valve in the performance should be A182F51, size ≥ 3 ", pressure rating ≥ 300 #. It is recommended that bidders of other brands in the same grade provide performance certification documents. The corresponding performance certification document requirements are detailed in the following performance requirements 1 and 2;Performance Requirement 1Copy of sales contract reflecting the recommended brand and model (including contract cover and signature page, as well as relevant technical attachments)Arrival acceptance materials (buyer's signed or stamped arrival acceptance form, on-site debugging report, usage certificate, or acceptance certificate)Performance Requirement 2The performance certification documents submitted by the bidder must at least reflect the following contents: brand and production factory, technical parameters of supporting control valves, supply quantity, usage environment, technical parameters/indicators, and arrival acceptance materials. Failure to submit performance certification documents, or if the provided performance certification documents cannot verify the above content, shall be deemed as invalid performance. 執行機構的品牌應滿足附錄A要求，投標人可推薦滿足以下條件與附錄A或相當于推薦品牌的其它品牌。2010年 1 月 1 日至投標截止日（以合同簽署時間為準）投標人或投標人所投執行機構的制造商應具有不少于2臺調節閥供貨的業績，且業績中執行機構的品牌與型號應與本次投標所用的一致。若該執行機構使用在氣動調節閥上，則業績中的調節閥閥體的材質應為A182F51，閥體尺寸≥20”，閥體壓力磅級≥1500#；若該執行機構使用在電動調節閥上，則業績中的調節閥的閥體材質應為A182F51，閥體尺寸≥3”，閥體壓力磅級≥300#，推薦相當于推薦品牌的其它品牌的投標人須提供業績證明文件，業績證明文件包括但不限于：1）銷售合同復印件和2）用戶簽字或蓋章的到貨驗收材料（到貨驗收單或調試驗收報告或其他可以證明合同項下貨物已經到貨驗收的有效證明材料）。投標人所提交的業績證明文件必須至少體現以下內容：合同簽署時間、合同簽署頁（國內貿易合同應有雙方蓋章，國際貿易合同應有雙方簽字或蓋章）、制造商名稱、貨物名稱、型號及生產工廠 若業績合同為年度協議，除提供年度協議外，還應提供相應的已到貨訂單，訂單內容或編號應與年度協議相關聯。同一個年度協議下提供1個或以上的訂單及與訂單對應的到貨驗收材料均算為1個有效業績。未提交業績證明文件，或通過所提供的業績證明文件無法認定滿足上述業績要求的，均視為無效業績。是否接受聯合體投標:不接受未領購招標文件是否可以參加投標:不可以4、
未曾在中國電力招標采購網（www.dlztb.com）上注冊會員的單位應先注冊。登錄成功后根據招標公告的相說明下載投標文件！

項目 聯系人：李楊  
咨詢電話：010-51957458 
傳真：010-51957412 
手機：13683233285 
QQ:1211306049 
微信：Li13683233285 郵箱：1211306049@qq.com

備注：欲購買招標文件的潛在投標人,注冊網站并繳納因特網技術服務費后，查看項目業主，招標公告，中標公示等，并下載資格預審范圍，資質要求，招標清單，報名申請表等。為保證您能夠順利投標，具體要求及購買標書操作流程按公告詳細內容為準，以招標業主的解答為準本。

編輯：chinabidding.co